Ide drive /yes/not recognized

Jose jose-vS8X3Ji+8Wg6e3DpGhMbh2oLBQzVVOGK at public.gmane.org
Wed Mar 7 16:26:27 UTC 2007


Hi All

I have this new machine that comes with dual core, it has 3 ide 
connector, one it's the default, already connected to a DVDrom (hdb), 
and one IDE master drive (hda), where I installed a dual boot with Suse 
10.2 and Centos 4.4, I have installed another IDE (hdf SUse)aside of 
another SATA (sda) drive on this machine, Suse recognizes the 3 drives + 
dvd, Centos only recognizes the primary master IDE, DVD, and SATA drive, 
but does not recognizes the second IDE, I  have no idea why it would 
happen on the Centos side, I connected a usb drive while on Centos and 
it recognized it within seconds.

I would appreciate any help, thanks in advance!

I am attaching what I get from DMESG on the Centos bootup:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 209
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: WDC WD1600JB-00REA0, ATA DISK drive
hdb: HL-DT-STDVD-RAM GSA-H50N, ATAPI CD/DVD-ROM drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, 
UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 131072 (order: 9, 3670016 bytes)
TCP: Hash tables configured (established 262144 bind 131072)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
P0P1 P0P3 P0P4 P0P5 P0P6 P0P7 P0P8 P0P9 UAR1 USB2 USB3 USB4 MC97 EUSB USB1
Freeing unused kernel memory: 164k freed
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security:  3 users, 4 roles, 355 types, 26 bools
security:  55 classes, 22582 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses 
genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x9800 ctl 0x9402 bmdma 0x8400 irq 217
ata2: SATA max UDMA/133 cmd 0x9000 ctl 0x8802 bmdma 0x8408 irq 217
ata1: SATA port has no device.
scsi0 : ata_piix
ata2: dev 1 cfg 49:2f00 82:746b 83:7f61 84:4023 85:7469 86:3c41 87:4023 
88:207f
ata2: dev 1 ATA-7, max UDMA/133, 625142448 sectors: LBA48
ata2: dev 1 configured for UDMA/133
scsi1 : ata_piix
  Vendor: ATA       Model: WDC WD3200KS-00P  Rev: 21.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
inserting floppy driver for 2.6.9-42.0.8.EL
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: unknown partition table
Attached scsi disk sda at scsi1, channel 0, id 1, lun 0
floppy0: no floppy controllers found
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 v1.1 addr 0xcfefc000 irq 177 Yukon-EC (0xb6) rev 2
divert: allocating divert_blk for eth0
sky2 eth0: addr 00:18:f3:1a:27:ee
MSI INIT SUCCESS
ACPI: PCI interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
hw_random: RNG not detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 185
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 185, pci mem f882a800
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 185, io base 00007000
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 193, io base 00007400
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 201, io base 00007800
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.3: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 177, io base 00008000
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 2-2: new low speed USB device using address 2
input: USB HID v1.00 Keyboard [KVM102UW] on usb-0000:00:1d.0-2
input: USB HID v1.00 Mouse [KVM102UW] on usb-0000:00:1d.0-2
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0384d60(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
ACPI: Power Button (FF) [PWRF]
EXT3 FS on hda2, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel-H+wXaHxf7aLQT0dZR+AlfA at public.gmane.org
cdrom: open failed.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
vxdmp: module license 'Proprietary.  Send bug reports to 
support-DTz5qymZ9yRBDgjK7y7TUQ at public.gmane.org' ta
ints kernel.
VxVM vxdmp V-5-0-34 added disk array OTHER_DISKS, datype = OTHER_DISKS
VxVM vxdmp V-5-0-34 added disk array DISKS, datype = Disk
 VxDMP1: p1 p2 p3 p4
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: unknown partition table
 VxDMP2: unknown partition table
vxportal: no version for "vx_free" found: kernel tainted.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1534196k swap on /dev/hda3.  Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses 
genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran-DTz5qymZ9yRBDgjK7y7TUQ at public.gmane.org>
microcode: No new microdata for cpu 0
IA-32 Microcode Update Driver v1.14 unregistered
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8189 buckets, 65512 max) - 356 bytes per conntrack
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
eth0: no IPv6 routers present


------------------------------------------------------------------------
Don't get soaked. Take a quick peek at the forecast 
<http://tools.search.yahoo.com/shortcuts/?fr=oni_on_mail&#news>
with theYahoo! Search weather shortcut. 
<http://tools.search.yahoo.com/shortcuts/?fr=oni_on_mail&#news>
--
The Toronto Linux Users Group.      Meetings: http://gtalug.org/
TLUG requests: Linux topics, No HTML, wrap text below 80 columns
How to UNSUBSCRIBE: http://gtalug.org/wiki/Mailing_lists





More information about the Legacy mailing list