<div dir="ltr"><div dir="ltr"><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Sep 23, 2020 at 2:27 PM D. Hugh Redelmeier via talk <<a href="mailto:talk@gtalug.org">talk@gtalug.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">| From: Russell Reiter via talk <<a href="mailto:talk@gtalug.org" target="_blank">talk@gtalug.org</a>><br>
<br>
| On Wed, Sep 23, 2020 at 9:40 AM D. Hugh Redelmeier via talk <<a href="mailto:talk@gtalug.org" target="_blank">talk@gtalug.org</a>><br>
| wrote:<br>
<br>
| I've made some progress and then lost it again. I had to take a high def<br>
| photo of the writing on the cable to read that the cable is rated 3.0 and<br>
| my mb is only rated 3.0 but the peripheral card is usb 3.1. I think this is<br>
| why the mb connection hangs the system on usb 3.0, but the peripheral 3.1<br>
| card does not. I'm not sure which iteration of usb provides "alternative"<br>
| bus capabilities, ie. video and up to 100w power.<br>
<br>
You don't care about video.  We don't know if you need larger power<br>
for the disk.<br>
<br>
| The mb type-c 3.0 port reports overcurrent when the device is attached and<br>
| won't boot.<br>
<br>
Reports to who?  How?  What do *you* observe<br></blockquote><div><br></div><div>udevadm monitor --env will report overcurrent events. It counted seven of them at one point, at least it did until I reformatted to NTFS. </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<br>
| On the adapter card the type is usb 3.1. and the device doesn't<br>
| hang the system when booting,<br>
<br>
When booting from what?  From the NVMe card via USB C?<br></blockquote><div><br></div><div>Sorry, I'm booting from a 250gib WD nvme in the primary m.2 slot on the motherboard. </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<br>
|  but it also won't enumerate the drive<br>
<br>
What do you mean "enumerate"?  What do you meant by "it"?<br></blockquote><div><br></div><div>I meant to say that the system wouldn't hang when plugged in but udevadm at one point was endlessly binding and unbinding the device pci nodes without transitioning to the usb mode alias. </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<br>
<br>
| ><br>
| > - reliably powering an NVMe drive, connected via USB C.<br>
| >   What are its specified power requirements?<br>
<br>
You didn't answer this question.<br></blockquote><div><br></div><div>Sorry I don't have the spec's on the device immediately available, but I'm going to look them up. </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<br>
| >   What can the ports provide?<br>
| >   USB C is a mess: one connector, several standards and options<br>
| >   within those standards, especially with respect to power.<br>
| ><br>
| <br>
| I may have to get a type-c 3.1 rated cable to go much further. It was all<br>
| working fine at one point before the power outage.<br>
<br>
I doubt that the cable is a problem.  But I guess that there's a<br>
chance.<br>
<br>
| I am updating the kernel<br>
| regularly on Fedora 31<br>
<br>
I think that that is a good idea but I think that it is unlikly to be<br>
the problem.<br></blockquote><div><br></div><div>I'm going to reboot now, given that I was finally able to get the NTFS partition recognized on the PCI-e cards Type-c port. </div><div><br></div><div>I don't necessarily hold much hope for consistency yet. I power off, unplug the power cable and press and hold the start button for a few seconds to see if I can dissipate any lingering bus voltage. I don't have a "manual" troubleshooting direction to do that, but things did start acting better when I started to do it. This was a practice I used to do diligently in the 90's, from before switched power supplies, but I never needed to do it much after 2000.</div><div><br></div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
---<br>
Post to this mailing list <a href="mailto:talk@gtalug.org" target="_blank">talk@gtalug.org</a><br>
Unsubscribe from this mailing list <a href="https://gtalug.org/mailman/listinfo/talk" rel="noreferrer" target="_blank">https://gtalug.org/mailman/listinfo/talk</a><br>
</blockquote></div><br clear="all"><div><br></div>-- <br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div>Russell<br></div></div></div></div></div></div>